Home > Is It > Is It Power Prob Or IDE Issue?

Is It Power Prob Or IDE Issue?

There is no definitive test to determine which component is at fault. So I shut down the computer for now.And now the same problem happens today. Maybe it will stop the questions – but I doubt it! It could be something else. "Could be that some services are turned off by default. http://htmltemplatesfree.net/is-it/is-it-the-power-source-need-educated-guesse-s.html

Reply vijay May 6, 2015 at 9:32 am please help me...my pc dvd drive not working.........i cleaned lens but it does not works.........in my dvd drive lens i found two pins So far, I’ve logged in the BIOS and changed to the default booting option, which didn’t help. Remove the RAM If you continue to experience the same problem with all the above hardware removed, remove the RAM from the motherboard and turn on the computer. Perform a clear CMOS procedure. Check This Out

But I'm thinking maybe if it was the logic board of the HDD then it wouldn't matter what if I removed or changed the IDE cable. Or you could just get that PSU from the store and see if it fixes your problem. Now do the same for the mobo end of that same cable. You can also check your motherboard or computer documentation for information on the beep codes.

Computer buying tips and help. solved Hard drive ide as slave to dvd drive solved Secondary hard drive keeps disappearing solved Need help installing secondary IDE Hard Drive solved Setting jumper cable for secondary ide hard But that's me; as they say, your mileage may vary. After waiting for a few moments, I decided to reset my computer by holding down the power button till it shut off and turned it back on again.When my computer tries

Even so, I would not use this as a primary HDD again, because it's bound to do that again.I managed to revive one old PC doing that, then used same HDD; Or you could try to switch the 4pin connector from the other HDD or one CDROM with the one from this HDD. Type the following command at the command prompt, and then press ENTER: %systemroot%\system32\restore\rstrui.exe where %systemroot% is the directory where the Windows operating system is located. You will then need to restart your computer and boot from the Windows System Recovery Disk.

His method revolves around attempting to narrow the cause of failure down to an individual, defective component, which means unplugging all non-essential devices and attempting to boot the machine. It performs a POST (power-on self test), initializes your computer’s hardware, and passes control over to the boot... Today I’d like to walk... Nothing worked.

The most effective of these is the deep reset, which temporarily halts power to the volatile memory on board all computers, thus resetting it to a factory fresh state. https://support.lenovo.com/us/en/documents/migr-4xvqal If the computer has a different beep code or if your computer was not beeping and is now beeping, turn off your computer and try the below suggestions. Read More computer shouldn’t be any different. If any USB devices (iPods, drives, phones, etc.) are connected, disconnect all of them as well.

Keep in mind that choosing a refresh or reset will cause some data loss. Ok the problem is that one time it didn't show up on "My Computer", so what I did then was restart the computer. Can't Delete Files from a CD-RW Disc 691 I can't read a particular recordable or rewriteable DVD disc with my DVD drive. It can either be a physical issue like power not getting to the drive or a IDE / SATA cable has come unplugged.

It’s the most basic troubleshooting methodology and no hardware repair guide is complete without it. If I were in your place, and I knew that my PSU is old, I would go ahead and replace the PSU first. Refer to the Hardware Maintenance Manual for directions. The preferred order of replacement is power supply, system board, then processor.

The boot drive (WDC5000AAKS) is on controller #1. Except I don't know if I have an extra Hard drive, except the one in my PS2 Which I use for games. Remove the CD-ROM from adapter and connect to DVD burner.

I really didn't know that this was there when I was going over the specs.

The exact location may vary from the example. Beep codes vary by the number of beeps and the time interval between beeps. Clean the laser lens with a cleaning kit or run some other discs after the cleaning kit and then try. Troubleshooting Installed Hard Disk Drives When you turn on your computer, you expect the system to start, load the operating system from the hard disk, and display the usual desktop or

Your power supply should have at least one cable going to the motherboard. For most troubleshooting, the boot sequence should be: Diskette drive (if installed) CD-ROM (if installed) Hard disk drive 0 If any installed bootable device, such as the hard disk drive, is Mark covers BIOS configuration settings, Windows configuration issues, BIOS startup error messages and solutions, and Windows 7 and 8 error recovery and advanced boot options. If the screen comes on but the system never displays any activity from the hard disk, your system (boot) hard disk isn't working.

Fix Windows Infinite Loading Screen Windows can also enter an unbootable state where the Windows loading icon displays, but the system never boots. If using Microsoft Windows XP, restart the computer, and then press F8 during the startup to start the computer in Safe Mode with a command prompt. Most of the time, pressing a F10, F11, or F12 on boot will give you the option of booting into the drive’s recovery system. Then I receive the "disk boot error" message.

Try a purchased CD  and see if that works. I know that this prevents you from playing movies (a frustrating find). This no nonsense chapter will help you to troubleshoot problems with your storage media, from hard drives to DVD-Rs. house70Jul 31, 2011, 10:49 PM As far as the OS goes, I am not sure about it, but it could be that some registry line got corrupted or deleted in time.